top of page

Best Effects Pedals for Synths: 6 Hardware Picks

Writer: Kamil
Kamil
1 day ago
7 min read

Updated: 8 hours ago

The best effects pedals for synths need to handle hotter signals without clipping, keep stereo patches wide and fit the way you play. A pedal that works nicely with guitar can still lose half your synth sound, bury you in menus or leave you without preset recall on stage. We compare six very different options by sound, connections, MIDI, presets and price, so you can find the right one for your rig.


Teal Strymon BigSky MX pedal on a wooden stool in front of vintage rack reverb units and a Premier amp

Note: This post contains affiliate links. If you choose to buy through them, I'll get a small kickback - at no extra cost to you. It helps me keep Noise Harmony going. Thank you!


Table of contents


Strymon BigSky MX: the best effects pedal for synth reverb


Top-down view of Strymon BigSky MX front panel with display showing Ensemble + IR preset and seven knobs
The BigSky MX display shows engines 1 and 2 running in parallel (PAR) on an Ensemble + IR preset, matching the dual-engine setup described here. SOURCE: Strymon

The Strymon BigSky MX is the best dedicated reverb here. Its two engines can run in parallel, in either series order or as separate left and right effects, with 12 reverb machines and stereo impulse responses lasting up to ten seconds. For a wide pad, run two restrained reverbs in parallel so the attack remains clear while each engine adds a different tail.


A synth normally sends a hotter line-level signal than a guitar, so select LINE in the Global Settings before raising the synth output. A direct setup runs synth to pedal to mixer or interface; an aux send lets several instruments share the effect, while interface outputs and inputs can create a DAW hardware insert. At the time of writing, BigSky MX is €699 at Thomann, and Strymon's BigSky MX overview demonstrates its dual-engine routing and main reverb sounds.




Strymon demonstrates the BigSky MX reverb engines, routing modes and main performance controls.



Eventide H90 Harmonizer®: the most complete multi-effect


Eventide H90 Harmonizer pedal on an amp, screen showing the Polyphonic Room program with lit footswitch LEDs
The H90 screen shows a Program pairing two algorithms, Polyphony and SP2016 Reverb, under the name Polyphonic Room. SOURCE: Eventide Audio

The Eventide H90 Harmonizer® suits synth players who want one box for reverb, delay, pitch effects, modulation and granular processing. Each Program combines two algorithms in series or parallel, while four inputs and four outputs can form two stereo paths or handle inserts. Its +14 dBu line-level input ceiling is the highest documented figure in this group.


For a bass patch, try subtle pitch processing before a short delay; for a pad, place modulation before reverb or feed both effects in parallel. Program Change recalls sounds, CC controls parameters and MIDI Clock keeps timed effects with a sequencer, using five-pin DIN or USB-C. H90 costs €879 at Thomann, and Eventide's H90 introduction shows the dual-algorithm workflow and performance controls.




Eventide shows how H90 combines two effects and controls them from its front panel.



Chase Bliss MOOD MKII: the best experimental texture pedal


Angled top view of black BOSS Space Echo RE-202 pedal with green mode selector panel and three footswitches
The RE-202's top panel includes a GUITAR/LINE input selector, a mode selector for head combinations and separate echo and reverb volume knobs. SOURCE: Chase Bliss

Chase Bliss MOOD MKII combines an always-listening Micro-Looper with a separate Wet Channel for spatial effects. MKII adds stereo processing, overdubbing, freezing, filtering and a Classic mode based on the first MOOD. A short captured sequence can sit behind the live synth, while Clock changes its pitch and timing in linked steps.


Stereo audio uses TRS sockets, so synths with separate left and right jacks need dual-TS-to-TRS breakout cables. Chase Bliss does not publish a line-level mode or maximum input figure, so start with the synth low and increase it while listening for unwanted clipping. MOOD MKII costs $399 from Chase Bliss, and the official MOOD MKII video manual explains how its two channels record and process sound.


  • Stereo, mono or mono-to-stereo over TRS

  • Two presets onboard; 122 recalled through MIDI

  • TRS MIDI with Program Change, CC and clock

  • 9V DC, center-negative, about 270mA



Chase Bliss explains how MOOD MKII records, loops and processes incoming audio.


Also check




BOSS RE-202 Space Echo: the best tape-style thickener


BOSS Space Echo RE-202 pedal seen from above at an angle, with green control panel and three footswitches
The RE-202 places Saturation and Wow & Flutter beside a green mode selector section, with ON/OFF, Memory and Tap footswitches below. SOURCE: BOSS

The BOSS RE-202 Space Echo gives synths multi-head tape echo, modulation, saturation and an independent stereo reverb. It adds a fourth virtual playback head and 12 head combinations to the familiar RE-201 idea. For an arpeggio, select LINE input, keep feedback below self-oscillation and set the repeat rate from the track tempo.


Four memories and the manual panel state are available without extra equipment, while MIDI Program Change reaches 127 memories through 3.5 mm TRS sockets. At €339 from Thomann, it is the best-value programmable stereo option here and the easiest to operate without menu work. BOSS's RE-202 demonstration covers its head combinations, Warp and Twist effects; players needing a more programmable delay should also read our Strymon TimeLine MX article.


  • True stereo quarter-inch inputs and outputs

  • Dedicated LINE setting; +7 dBu maximum input

  • Four onboard memories; 127 through MIDI

  • Micro-USB port is for program updates only



BOSS demonstrates the RE-202 playback heads, tape controls and performance effects.



TC Electronic FLASHBACK 2: the affordable stereo delay


TC Electronic Flashback 2 Delay and Looper pedal, angled view showing four knobs, footswitch and stereo output jacks
The blue Flashback 2 from an angle, with four knobs, a subdivision toggle, and stereo out jacks on the side. SOURCE: TC Electronic

The TC Electronic FLASHBACK 2 is the lowest-priced stereo delay in this group. It provides eight delay types, including Tape, Analog, Reverse, Dynamic and the octave-shifted Crystal mode, plus three TonePrint slots. Its pressure-sensitive MASH footswitch can change effect-specific settings such as feedback, modulation or the amount of octave processing while you play.


FLASHBACK 2 can process a stereo synth and includes a looper with up to 40 seconds in mono or 20 seconds in stereo. TC Electronic does not give a maximum line-level input figure, so start with the synth output low and raise it while checking for unwanted clipping. At the time of writing, it is €105 at Thomann, which makes it a useful first stereo pedal when presets and MIDI control are not essential.


  • Mono or stereo input and output

  • Eight delay types and three TonePrint slots

  • 40-second mono or 20-second stereo looper

  • Pressure-sensitive MASH footswitch



Walrus Audio Slö: an affordable mono ambient option


Blue Walrus Audio Slö reverb pedal at an angle, with crescent moon artwork, five knobs and bypass and sustain footswitches
The Slö has Decay, Filter, Mix, X and Depth knobs, a sine/warp/sink toggle and a dedicated Sustain footswitch next to Bypass. SOURCE: Walrus Audio

The Walrus Audio Slö Multi Texture Reverb is the intentional exception in this list. Dark adds a sub-octave to the reverb, Rise produces automatic swells and Dream creates a sustained pad. Those sounds work well behind a simple mono pad or lead, especially when the Sustain switch holds the reverb under new notes.


Slö has one input and one output, so it does not preserve a synth's stereo image and cannot create stereo from a mono source. It also has no MIDI or full preset storage, and Walrus does not publish line-level headroom, so begin with a low synth output. Thomann showed conflicting prices of €179 and €211 on November 11, 2026, so check the live price; choose the separate Slöer instead if stereo is essential.


  • Mono input and mono output

  • No confirmed line-level mode

  • No MIDI or complete preset storage

  • 9V DC, center-negative, 100mA minimum




Which synth effects pedal should you buy?


Choose BigSky MX when stereo reverb quality, flexible routing and instant preset recall matter most. H90 makes more sense for a studio or computer-free live rig that needs many effect types, while MOOD MKII is the creative choice for looping and altered textures. RE-202 offers programmable stereo tape echo, while FLASHBACK 2 covers basic stereo delay and looping for much less. Slö only makes sense when its ambient sound matters more than stereo, MIDI and presets.


Add Big Stereo Reverb to Your Synth


BigSky MX accepts line-level stereo signals and stores enough presets for a full live set or several studio projects. Check the current Thomann price and availability before choosing your power supply and cables.



More information



Frequently Asked Questions


Can you use guitar effects pedals with a synthesizer?


Yes. Start with the synth output low because its line signal can be hotter than a guitar signal, then raise it until the level is healthy without unwanted distortion. A hot synth output normally overloads the input rather than damaging the pedal.


Do I need a reamp or DI box between a synth and a pedal?


Usually, no. A pedal with a proper line setting can connect directly, and many other pedals work if you reduce the synth or aux-send level. Use attenuation or a reamp box only when the pedal keeps clipping at practical settings; a DI box is normally placed after the pedal when a balanced feed is needed.


Does a synth pedal need true stereo connections?


No, but true stereo is important when the original patch already contains panning, stereo chorus or separate left and right processing. Mono-to-stereo pedals can make one input wider, but they cannot preserve stereo information that was removed at the input.


Should my first synth pedal be reverb, delay or multi-effects?


Reverb is the safest first choice for pads, leads and simple mono synths. Choose delay if rhythmic sequences are your main sound, or a multi-effect such as H90 when you need modulation, pitch, delay and reverb from one box.


ABOUT THE AUTHOR

Kamil

Kamil

Sound designer, synths and keys


Kamil is our synth and keys guy: if it has black and white keys, he has played it. He grew up on progressive rock and metal and designs sounds for Noise Harmony. His sounds have gone into work with KORG, Arturia, Xfer Records (Serum 2) and many more. Off the clock he plays in his own bands: music is simply his whole life.



FOLLOW US ON


Comments


GET -10% DISCOUNT

Sign up for our newsletter today and unlock an exclusive offer: receive -10% discount just for joining!


Stay ahead with updates on new products, promotions, coupons, and much more.

Thank you for subscribing to our newsletter!

bottom of page