top of page

Eventide SplitEQ 2 Adds Dynamic Bands and Masking Detection

Writer: Rafal
Rafal
7 minutes ago
6 min read

Eventide SplitEQ 2 launched on November 17 with six dynamic bands, track-to-track masking detection and separate dynamics for transient and tonal signals. It keeps the original plugin’s unusual Structural Split processing but adds much more control for mixing and mastering. The main question is whether those additions justify moving beyond a conventional dynamic EQ, especially once latency enters the picture.


Eventide SplitEQ 2 plugin window at an angle, showing EQ curves, two band panels with dynamics controls and Transient/Tonal

Note: This post contains affiliate links. If you choose to buy through them, I'll get a small kickback - at no extra cost to you. It helps me keep Noise Harmony going. Thank you!


Table of contents


Eventide SplitEQ 2 separates transients from tone


Eventide SplitEQ 2 front view with numbered EQ bands, paired Transient and Tonal curves, and the Split bar at the bottom
The Split bar along the bottom holds the Separation, Decay and Smooth settings, and each numbered band shows separate Transient and Tonal gain values. SOURCE: Eventide Audio

Structural Split divides incoming audio into Transient and Tonal streams before the EQ processes them. Rapidly changing material goes to the Transient stream, while more stable content is treated as Tonal. Unlike compressor-style detection, this separation does not depend on the signal crossing a level threshold. The two streams reconstruct the original input when summed without different processing.


That split lets you change the initial hit of a snare without applying the same EQ to its ring, or soften a guitar pick while leaving the sustained note alone. White controls move both streams together, while green and blue controls edit Transient and Tonal independently. SplitEQ 2 effectively gives each stream its own parallel EQ and dynamics processing, using 64-bit double-precision processing throughout.


Six bands now handle compression and expansion


Eventide SplitEQ 2 at an angle with bands 1 and 3 expanded to show threshold, ratio, attack and release
Bands 1 and 3 are expanded to show their dynamics controls, including the threshold, ratio, attack and release values and the key source selector. SOURCE: Eventide Audio

Six of the eight EQ bands now include configurable compression and expansion. The remaining two bands are dedicated high-pass and low-pass filters, while the numbered bands offer peak, shelf, notch, tilt shelf and bandpass shapes. Negative Dynamic Range values apply compression, positive values apply expansion, and the Range setting limits the maximum change.


Each dynamic band includes threshold, ratio, attack and release controls, with Auto modes that derive starting values from the incoming audio. Detection can listen to the relevant Transient and Tonal streams, the unsplit signal or an external sidechain. You can also choose in-band or full-spectrum detection, giving each band six possible sidechain setups.


The interface now lets you create a band by clicking directly on the frequency plot. An existing static gain move can also be converted into a dynamic range, which resets its static gain to zero. Eventide’s official overview video is titled SplitEQ 2 Overview: Dynamic Bands, Masking, Sidechain & More.



Eventide demonstrates SplitEQ 2’s dynamic bands, masking display and sidechain choices in the official overview.


Also check



Masking Detection compares two tracks inside the plugin


Close-up of the SplitEQ 2 Global Dynamics panel with Pre/Post, Thresh, Knee, Ratio, Attack and Release controls
This close-up shows the Global Dynamics panel rather than the masking display: it has a Pre/Post switch, a Split key source and separate threshold and attack values. SOURCE: Eventide Audio

Masking Detection compares two tracks that both have SplitEQ 2 inserted and highlights areas where one may obscure the other. Realtime mode shows immediate conflicts, while Histogram mode builds an average picture over time. The direction control swaps which track is treated as the masker, so you can check the problem both ways.


The histogram distinguishes potential masking before and after EQ, making it easier to see if a change actually helped. Sensitivity runs between 1 and 100 percent, with lower settings showing only the strongest conflicts. Eventide warns that the plugin cannot read post-fader track levels, so the display should support your ears rather than make the final call.


Global Dynamics adds full-spectrum compression or expansion for the Transient and Tonal streams. It can sit before or after the EQ bands and includes split, unsplit and external sidechain choices. This is useful when the whole transient stream needs control and setting several separate dynamic bands would only make the session harder to manage.



What changed from the original SplitEQ?


Eventide SplitEQ 2 in Pan view with bands set to M, S, L and R and curves for Main, Mid, Side, Left and Right
In the Pan view, each band can be assigned to Mid, Side, Left or Right, and the plot shows a color-coded curve for each channel. SOURCE: Eventide Audio

SplitEQ 2 adds dynamics and mix-wide analysis to the original plugin’s transient-and-tonal EQ idea. The first SplitEQ already had eight bands, separate stream controls, stereo panning, spectrum analysis and global EQ scaling. Version 2 adds dynamic processing to six bands, Global Dynamics, masking displays, sidechains and direct band creation on the plot.


Seven new source tunings cover Distorted Guitar, Strings, Synth Lead, Synth Pad, Horn, Horn Section and Woodwinds. Individual bands can now target Left, Right, Mid or Side, or use continuous pan and width controls. The factory library also grows beyond 290 presets, compared with more than 150 in the original.


The important limitation is latency. Structural Split needs an audio history, producing 3,592 samples at 44.1 or 48 kHz, with higher figures at higher sample rates. Eventide says active processing is unsuitable for real-time use, although Tracking Bypass can disable every instance in a session and remove their latency contribution while recording.


SplitEQ 2 therefore makes the most sense for detailed mixing and mastering after tracking is finished. It offers a different approach to conventional dynamic EQ because it can process an attack separately from the sustained material in the same frequency area. Musicians who mainly need simple corrective EQ or low-latency monitoring may not need its extra processing and setup.


Price and availability


At the time of writing, Eventide lists SplitEQ 2 for $99, with $199 crossed out, but the company has not published an end date for that price. Existing SplitEQ owners can log in for upgrade or loyalty pricing, although there is no single public upgrade price. A 14-day demo is available for anyone who wants to check the workflow and latency in their own sessions.


Angled view of the Eventide SplitEQ 2 window with separate Transient and Tonal EQ curves and dynamic band controls
Each band in SplitEQ 2 draws separate curves for the Transient and Tonal streams, with dynamics settings shown in green and blue. SOURCE: Eventide Audio

SplitEQ 2 runs on Windows 10 or later in 64-bit AAX and VST3 formats. Mac users need macOS 10.14 or later, with Intel and Apple Silicon support through AAX, AU and VST3. An iLok account is required, but a USB dongle is optional, and each license allows two activations.


Plugin Boutique had not added SplitEQ 2 to its Eventide catalog at the November 17 research cutoff, so check its current listing before buying there. Current details, the demo and maker pricing are available on the official Eventide SplitEQ 2 page.


Check SplitEQ 2 at Plugin Boutique


Eventide’s $99 promotional price has no published end date. Check Plugin Boutique for current availability and pricing before the offer changes.



More information



Frequently Asked Questions


Is Eventide SplitEQ 2 suitable for recording with live monitoring?


No. Structural Split introduces significant latency, and Eventide says its active processing is not suitable for real-time use. Tracking Bypass can disable all SplitEQ 2 instances together while you record and restore them afterward.


Does SplitEQ 2 require an iLok USB dongle?


No. You need an iLok account, but each of the two allowed activations can use a computer or an iLok USB dongle. Activations can be moved through iLok License Manager.


Which plugin formats does SplitEQ 2 support?


SplitEQ 2 supports 64-bit AAX and VST3 on Windows 10 or later. On macOS 10.14 or later, it supports AAX, AU and VST3 on Intel and Apple Silicon systems.


Can original SplitEQ owners upgrade to SplitEQ 2?


Yes. Eventide provides upgrade or loyalty pricing after customers log in, but it does not publish one universal upgrade price. Existing owners should check their account for the applicable offer.



ABOUT THE AUTHOR

Rafał

Rafał

Sound designer, guitar tone, mixing and mastering


Rafał is the guitar tone person at Noise Harmony, from amps and effects to production, mixing and mastering. Plugins and the technical side of sound are his life. Over the years he has worked with Arturia, KORG, Xfer Records (Serum 2) and plenty of others, and he still plays in his bands whenever he can. Music isn't a job for him, it's everything.



FOLLOW US ON


Comments


GET -10% DISCOUNT

Sign up for our newsletter today and unlock an exclusive offer: receive -10% discount just for joining!


Stay ahead with updates on new products, promotions, coupons, and much more.

Thank you for subscribing to our newsletter!

bottom of page